Skytrak 6036 Service Manual Bedienungsanleitung Seite 159
- Seite / 460
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
5.23
Model 6036 Legacy
Axles, Drive Shafts, Wheels and Tires
5.5.2 Wheel Cleaning
Remove all rust, corrosion, dirt and other foreign material
from all metal surfaces. In particular, the bead area (tire-
to-wheel mounting surface) must be especially clean.
5.5.3 Wheel Inspection and Replacement
Check all surfaces of the wheel for rust, corrosion,
cracks, bent flanges, deep marks or gouges. Replace a
damaged, worn or cracked wheel. NEVER rework, heat,
weld or braze a wheel rim.
Inspect the valve core and stem. Replace the entire valve
if either component is damaged.
5.5.4 Installing Wheel and Tire Assembly
Onto Vehicle
IMPORTANT: The wheel and tire assemblies must be
installed with the directional tread pattern “arrows” facing
in the direction of forward travel (Fig. 5-18).
Figure 5-18 Install Wheel and Tire Assemblies
WARNING: Dirt and rust prevent the tire
from seating properly on the wheel, which
could result in an explosive separation. Such
explosions could result in death or severe
personal injury to the tire installer and to those
in the area.
WARNING: Damaged, modified,
repaired or mis-matched wheels and tires, or
dirt and rust prevent the tire from seating
properly on the wheel, which could result in an
explosive separation. Such explosions could
result in death or severe personal injury.
• NEVER rework, heat, weld or braze a
wheel rim.
• Clean and inspect the wheel rim before
installing a new tire. Verify that the wheel
rim diameter exactly matches the tire
rim diameter molded into the tire.
• Inspect the inside of the tire for dirt,
foreign material, loose cords, cuts,
penetrating objects and other damage.
DO NOT use tires with irreparable
damage.
PT07202
Tread “arrows” must
point forward
Install tires onto
wheels to rotate in
proper direction
- Service Manual 1
- EFFECTIVITY PAGE 3
- SECTION CONTENTS 5
- Section Subject Page 6
- Section 1 9
- 1.1 INTRODUCTION 10
- 1.2 OWNERS/OPERATORS MANUAL 10
- 1.3 TRAINING MECHANICS AS 11
- OPERATORS 11
- 1.4 SAFETY INFORMATION 11
- DANGER: 12
- WARNING: 12
- CAUTION: 12
- 1.6 SAFETY INSTRUCTIONS 13
- Safety Practices 14
- 1.6.3 General Hazards 14
- 1.6.4 Operational Hazards 14
- 1.8 HAZARD/EMERGENCY 15
- INFORMATION DECALS 15
- Domestic: 1-877-554-5438 15
- International: 1-717-485-5161 15
- Section 2 17
- 2.2 INTRODUCTION 20
- 2.3 TORQUES 21
- 2.4 METRIC CONVERSION FACTORS 22
- 2.4.2 Approximate Metric to 23
- American Conversions 23
- 2.5 SPECIFICATIONS 24
- 2.5.2 Vehicle Weights 26
- 2.5.3 Attachment Weights 27
- 2.5.6 Electrical System 28
- 2.5.9 Hydraulic System 31
- 2.5.10 Tires 31
- 4000 x 24 32
- 2.6.2 Axle Wheel Ends 33
- 2.6.3 Transmission 33
- 2.6.5 Hydraulic System 34
- 2.6.6 Engine 34
- 2.6.7 Drive Shaft Splines 35
- 2.6.8 General Anti-Corrosion 35
- 2.6.9 Electrical 35
- 2.7 CLEANING 36
- 2.8 REPLACEMENT 37
- 2.9 HOSES AND TUBES 37
- 2.10 BEARINGS 37
- 2.11 PRESSURE TESTING AND 38
- ADJUSTMENT 38
- 2.12.8 After Engine Service 40
- 2.12.9 After Boom Service 40
- 2.12.10 After Axle Service 40
- Section 3 41
- 3.1 BOOM SYSTEM COMPONENT 42
- 3.2 BOOM SYSTEM 43
- 3.3 BOOM ASSEMBLY MAINTENANCE 43
- Front Top Wear Pads 44
- Tilt Cylinder Hoses 45
- Hose Reel Side Plate 51
- Hose Reel Assembly 51
- Auxiliary Hydraulics Hoses 52
- Cylinder Rod End Pin 52
- Boom Rear Wear Pads 53
- Upper Rear Wear Pads 53
- 3.3.3 Outer Boom Removal 54
- Attachment Tilt Tubes 56
- Cylinder Pivot Pins 58
- Cylinder Base End Pin 59
- 3.3.4 Outer Boom Installation 60
- Slave Cylinder Bearings 61
- Tube Assemblies 67
- Lower Wear Pads 68
- Boom Front Wear Pads 72
- 3.3.6 Inner Boom Installation 73
- Inside the Inner Boom 74
- Boom Front Side Wear Pads 77
- Intermediate Boom Sections 79
- Hydraulic Coupler and Nipple 82
- Cylinder Base End Pivot Pin 82
- 3.3.7 Boom Chains 84
- Adjustment Locknuts 89
- Extend Chain Installation 92
- Retract Chain Removal 94
- 3.3.8 Boom Wear Pads 96
- Intermediate Boom 97
- Outer Boom 98
- 3.4 QUICK ATTACH ASSEMBLY 99
- 3.4.3 Quick Attach Removal 100
- 3.5 TROUBLESHOOTING 101
- Problem Cause Remedy 101
- Model 6036 Legacy 104
- Section 4 105
- Cab and Covers 105
- COMPONENT TERMINOLOGY 106
- 4.2 OPERATOR’S CAB 107
- 4.3 OPEN CAB COMPONENTS 108
- 4.3.4 Brake Pedal and Valve 114
- Assembly Replacement 119
- 4.3.8 Electrical Components 121
- 4.4 ENCLOSED CAB (OPTIONAL) 123
- COMPONENTS 123
- 4.4.5 Door and Latches 127
- 4.4.6 Windows 128
- 4.5 CAB REMOVAL 129
- 4.6 CAB INSTALLATION 133
- 4.7 ACCESS PANELS AND COVERS 136
- Section 5 137
- 5.2 GENERAL INFORMATION 139
- 5.3 AXLE ASSEMBLIES 139
- 5.3.4 Axle Specifications 140
- 5.3.5 Axle Maintenance 140
- 5.3.6 Axle Replacement 141
- Troubleshooting 150
- 5.4 DRIVE SHAFTS 151
- 5.4.2 Drive Shaft Maintenance 152
- 5.4.3 Drive Shaft Removal 152
- 5.4.4 Drive Shaft Disassembly 153
- 5.4.6 Drive Shaft Assembly 155
- Direction of Forward Travel 157
- WARNING: Damaged, modified 159
- Section 6 163
- Transmission: ZF 4 WG-98 TC 163
- 6.1 TRANSMISSION ASSEMBLY 164
- 6.2 TRANSMISSION DESCRIPTION 165
- 6.3 TRANSMISSION OPERATION 165
- 6.6 TRANSMISSION MAINTENANCE 166
- 6.7 TRANSMISSION REPLACEMENT 168
- 6.8 TOWING A DISABLED VEHICLE 175
- 6.9 TROUBLESHOOTING 176
- Section 7 179
- Engine: Cummins 4BT3.9 179
- 7.1 INTRODUCTION 180
- 7.2 SAFETY INFORMATION 182
- 7.3 ENGINE SERIAL NUMBER 184
- 7.4 SPECIFICATIONS AND 184
- MAINTENANCE INFORMATION 184
- 7.5 STANDARD PRACTICES 184
- 7.6 ENGINE COOLING SYSTEM 185
- Heater Replacement 188
- 7.7 ENGINE ELECTRICAL SYSTEM 192
- 7.8 FUEL SYSTEM 193
- 7.8.1 Diesel Fuel 194
- 7.9 ENGINE EXHAUST SYSTEM 201
- 7.10 AIR CLEANER ASSEMBLY 202
- 7.11 ENGINE REPLACEMENT 203
- 7.11.3 Engine Installation 208
- 7.12 ENGINE STORAGE 215
- 7.13 TROUBLESHOOTING 216
- Section 8 217
- Hydraulic System 217
- 8.1 HYDRAULIC COMPONENT 219
- TERMINOLOGY 219
- 8.2 SAFETY INFORMATION 220
- 8.3 SPECIFICATIONS 221
- 8.4 HYDRAULIC FLUID 221
- Replacement 222
- 8.7 HYDRAULIC SYSTEM TESTING 226
- 8.8 HYDRAULIC CIRCUITS AND 229
- TROUBLESHOOTING 229
- 3. Air in the lines 241
- Load Sense 262
- Pressure 262
- Description 268
- PROCEDURE 274
- 8.10 HYDRAULIC RESERVOIR 276
- 8.11 HYDRAULIC SYSTEM PUMP 277
- 8.11.2 Pump Replacement 278
- 8.12 VALVES AND MANIFOLDS 284
- 8.12.2 Main Control Valve 286
- 8.12.4 Service Brake Valve 305
- 8.12.5 Shuttle Valve 309
- 8.12.6 Power Steering Valve 310
- 8.12.7 Steer Select Valve 312
- 8.13 HYDRAULIC CYLINDERS 316
- 8.13.5 Slave Cylinders 321
- 8.13.7 Lift/Lower Cylinder 330
- 8.13.8 Frame Sway Cylinder 334
- 8.13.11 Steering Cylinders 351
- Section 9 353
- Electrical System 353
- 9.1 ELECTRICAL COMPONENT 355
- 9.2 SERVICE WARNINGS 357
- 9.3 SPECIFICATIONS 357
- 9.5 WIRING HARNESSES 358
- 9.5.3 Cleaning and Drying 359
- 9.5.4 Inspection and Repair 359
- 9.5.5 Installation 359
- 9.5.6 Wire Code and Color 359
- 9.6 FUSES AND RELAYS 360
- 9.7 ELECTRICAL SYSTEM 362
- 9.10 ENGINE START CIRCUIT 409
- 9.10.2 Starter 410
- 9.11 CHARGING CIRCUIT 411
- 9.11.2 Battery 414
- 9.12 ELECTRICAL SYSTEM 417
- 9.12.2 Back-Up Alarm 418
- 9.12.3 Instrument Cluster 419
- 9.13.2 Windshield Wiper Motor 422
- 9.13.3 Roof Wiper Switch 424
- 9.13.4 Roof Wiper Motor 424
- 9.14.1 Cab Heater Controls 427
- 9.15 SWITCHES AND SOLENOIDS 428
- 9.15.2 Fuel Shut-off Solenoid 430
- 9.15.4 Park Brake Switch 433
- 9.15.7 Steering 441
- 9.15.8 Steer Select Switches 443
- 9.15.9 Steer Select Valve 444
- 9.15.13 Engine Block Heater 448
- 9.15.15 Hourmeter 451
- Section 10 453
- Accident Prevention Tags 457
- 8990403 Origin 5/00 458
- JLG Worldwide Locations 460
Verwandte Produkte und Handbücher für Spezialmaschinen Skytrak 6036 Service Manual
Spezialmaschinen Skytrak 10054 Bedienungsanleitung
(412 Seiten)
(412 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.344 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern